A sewing machine that skips stitches in the festival rush costs more than any repair bill. Most breakdowns come from lint, dry parts and old needles, and all three are prevented by a few minutes of sewing machine maintenance a day. Here is the daily, weekly and monthly routine for a tailoring shop, and how to tell when it is time to call the mechanic.

Sewing Machine Maintenance for a Tailoring Shop — sewing machine maintenance

Why Machines Fail in the Busy Season

Machines rarely break in the quiet months. They break in the weeks before Diwali or a wedding season, when they run ten hours a day and nobody has time to clean them. The lint builds up under the needle plate, the oil dries out, the same needle is used for a week, and one evening the machine starts skipping stitches on a bride's blouse.

Almost none of this is a real fault. It is neglect that shows up under load. A shop that cleans and oils on a fixed routine has far fewer stoppages, and the stoppages it does have are small ones it can fix itself.

The routine below is for the machines most Indian shops run: industrial single-needle lockstitch machines, overlock machines, and the domestic or tailoring machines many shops still keep for small jobs. Always check the manual for your model first; where it disagrees with this guide, the manual wins.

Every Day: Five Minutes at Closing

Clean out the lint

Remove the needle plate and brush out the lint around the feed dogs and the bobbin area. Use a small brush, never your breath; blowing pushes lint deeper into the machine and adds moisture. On an overlock, open the front cover and brush out the cutting area, where trimmed threads collect fastest.

Wipe the machine down

Wipe the bed, the thread path and the area round the needle with a dry cloth. Oil and lint together make a grey paste that ends up on the next customer's cloth.

Check the oil on industrial machines

Many industrial machines have an oil sump with a level mark, and some have a small window that shows oil splashing while the machine runs. Check the level and top up with sewing machine oil only. Never use cooking oil, engine oil or general household oil; they thicken and gum up the mechanism.

Cover it

A cover keeps dust off overnight. In a shop near a road, it makes a noticeable difference to how much lint and grit gets inside.

Every Week: Twenty Minutes

Oil the points the manual shows

Domestic and tailoring machines without an oil sump need a drop of oil at each point marked in the manual: usually the needle bar, the presser bar, the shuttle race and the moving joints under the bed. One drop at each point is enough. Run the machine on a scrap of cloth afterwards to soak up any extra before stitching a customer's garment.

Clean the bobbin case and shuttle

Take out the bobbin case, brush it, and wipe the shuttle race. A single strand of thread wound round the hook is enough to cause looping and thread breaks.

Check the belt

Look at the motor belt for cracks and fraying, and check the tension: it should move a little when pressed, not sag and not feel tight as a wire. A slipping belt shows up as a machine that slows down on thick seams.

Test the stitch

Stitch a line on a double scrap of the fabric you use most. Look at both sides. A good lockstitch looks the same on top and underneath, with the threads locking inside the cloth. Loops underneath usually mean the top tension is too loose; loops on top usually mean it is too tight or the bobbin tension is off.

Needles: The Cheapest Fix There Is

A blunt or bent needle causes more skipped stitches, broken threads and pulled fabric than any other part, and it costs a few rupees to replace.

Change the needle after roughly every eight hours of stitching, at the start of every new garment in delicate fabric, and immediately after it hits a pin or a zip. A needle that has struck something hard may look straight and still be burred at the point, and a burr snags silk and georgette.

Use the right needle for the fabric and thread. A fine needle for chiffon and georgette, a medium one for cotton and silk, a heavier one for denim and suiting; our guide to needles and thread for each fabric has the full table. Make sure the needle system matches the machine. An industrial needle and a domestic needle are not interchangeable, even when they look alike.

Fit the needle all the way up, with the flat side or the long groove facing the way the manual shows. A needle fitted slightly low or turned slightly round is the commonest reason a newly serviced machine skips stitches.

Every Month: An Hour, or a Visit

Once a month, or every few months on a lightly used machine, do the jobs that take longer: clean under the bed, check and tighten loose screws, look at the feed dogs for wear, and clean the tension discs by running a strip of soft cloth between them with the presser foot up.

On an industrial machine with an oil sump, change the oil at the interval the manual gives, and wipe out the sludge from the sump when you do.

Then have a mechanic in at least once or twice a year, before the busy seasons rather than during them. Timing, hook clearance and motor problems need a trained hand. A visit in August or September is far cheaper than a breakdown in October.

A Simple Maintenance Register

Shops with several machines lose track of which one was oiled, which one had its needle changed and which one the mechanic looked at. A one-line record per machine solves it.

MachineDailyWeeklyMonthlyLast mechanic visit

Machine 1, lockstitch

Lint, wipe, oil level

Bobbin case, belt, stitch test

Under-bed clean, screws, tension discs

Date and what was done

Machine 2, overlock

Lint, cutter area

Oil points, blades

Loopers, screws

Date and what was done

Machine 3, tailoring

Lint, wipe

Oil points, bobbin

Under-bed clean

Date and what was done

Put it on the wall beside the machines. When something goes wrong, the register tells the mechanic what has and has not been done.

When It Is Time to Call the Mechanic

Clean, oil and change the needle first. If the problem stays, it is a job for the mechanic.

Skipped stitches with a new, correctly fitted needle: the timing or hook clearance may be off.

The needle hits the plate or the hook: stop immediately. Running it will damage the hook.

Grinding, knocking or new noises: something is loose or worn inside.

The machine runs hot or smells of burning: often the motor or the belt. Switch it off.

The fabric will not feed evenly with clean feed dogs: the feed dogs may be worn or set too low.

If you are deciding whether to repair an old machine or replace it, our guide to which machines a new tailoring shop needs covers what to look for in a new or second-hand one.

Frequently Asked Questions

How often should a sewing machine be oiled?

An industrial machine with an oil sump needs its level checked daily and topped up when low. A domestic or tailoring machine without a sump needs one drop at each oiling point roughly once a week in a busy shop. Always use sewing machine oil only.

How often should I change the sewing machine needle?

After about every eight hours of stitching, at the start of each garment in delicate fabric, and immediately after the needle hits a pin or a zip. A burred needle snags fine fabric even when it looks straight.

Why is my sewing machine skipping stitches?

Most often a blunt, bent or wrongly fitted needle, the wrong needle for the fabric, or lint in the bobbin area. If a new, correctly fitted needle and a clean machine do not fix it, the timing may need a mechanic.

How often should a tailoring shop have its machines serviced?

At least once or twice a year by a mechanic, ideally before the busy seasons, with the daily, weekly and monthly cleaning done in the shop in between.

Where Juvee Helps

A machine stopped in the rush means orders slipping, and the first thing a shop needs then is to know which garments are due and which karigar can take them over. Juvee shows every order's stage and due date in one list, so a lost afternoon can be planned around rather than discovered at delivery; see job management. If the busy season is already here, the guide to handling a rush order without losing the rest helps too. The Basic plan is free with no time limit, and paid plans start at ₹10,190 a year including GST; the pricing page lists every plan.