A seam is the line that holds a garment together, and the type of seam decides how long it lasts, how it looks inside and how it feels against the skin. Here are the types of seams a tailoring shop uses every day, when to use each one, and the seam finishes that stop the inside from fraying after the first wash.

Why the Seam Matters
Customers judge a garment from the outside, but they keep or return it because of the inside. A blouse whose side seams fray after three washes, a kurta whose seam scratches under the arm, or a trouser whose seat splits when he sits down are all seam failures, and they come back to the shop.
Choosing the seam is not about doing the most work. It is about matching the seam to the fabric, the garment and the place on the garment where it sits. A heavy French seam in a thick denim is as wrong as a raw plain seam in a chiffon that will fray to nothing.
Most shops use three or four seams for nearly everything. Knowing the other few, and when they are worth the time, is what separates a garment that looks hand-finished from one that looks mass-produced.
The Plain Seam
The plain seam is the base of everything. Two pieces of fabric placed right sides together and stitched along the seam line, with the allowance left inside and then pressed open or to one side.
It is quick, flat, easy to alter later and suits almost any fabric. On its own, though, the raw edges inside will fray, so a plain seam is almost always finished with one of the methods further down.
Use it for: most side seams, shoulder seams and sleeve seams in blouses, kurtas, salwars and shirts, wherever the garment may later need letting out or taking in.
The French Seam
A seam stitched twice to hide the raw edge completely. First the pieces are stitched with wrong sides together, close to the edge; the allowance is trimmed; then the fabric is folded the other way, right sides together, and stitched again so the first seam and its raw edge are enclosed inside the second.
It looks beautiful inside and does not fray at all, but it adds bulk and is hard to alter. It also does not suit curves well.
Use it for: thin and sheer fabrics such as georgette, chiffon, organza and fine cotton, where an overlocked edge would show through or be too heavy. Dupatta joins, sheer sleeves and the side seams of lightweight kurtas and nighties.
The Flat-Felled Seam
A strong, flat seam where one allowance is trimmed short, the other is folded over it, and the fold is stitched down to the garment. Both raw edges are enclosed, and there are two rows of stitching visible on the outside.
It is the strongest seam a tailoring shop makes, and the one that survives hard washing and hard wear. It takes time and skill on curves.
Use it for: shirt side seams and sleeve seams, trouser inside leg seams, work wear and uniforms, and anything in denim or heavy cotton. It is also why a well-made shirt looks finished inside.
The Overlocked Seam
A plain seam whose allowance is trimmed and finished together by an overlock machine, which cuts the edge and wraps it in thread in one pass. Most ready-made garments use it, and most busy shops use it for speed.
It is fast, neat and prevents fraying. On its own it is not the strongest seam, so for stress points it is often combined with a straight stitch line inside the overlock. Our guide on which machines a new tailoring shop needs covers when an overlock machine is worth buying.
Use it for: everyday salwars, kurtas, nighties, kids' wear, and the bulk of production and uniform work.
The Bound Seam
A plain seam pressed open, with each raw edge wrapped in a thin strip of bias fabric. Sometimes called a Hong Kong finish. It is the cleanest finish for an unlined garment in a fabric that frays, and it looks expensive when someone sees the inside.
Use it for: unlined jackets, blazers and coats, silk blouses without lining, and occasion wear where the inside may be seen.
The Lapped and Topstitched Seam
One piece is laid over the other and stitched from the outside, with the stitching visible as a design line. A topstitched seam is a plain seam pressed to one side and stitched again from the outside to hold it flat.
Use it for: yokes, pocket edges, plackets, collars and anywhere the stitching line is part of the look, as well as on heavy fabrics that will not press flat on their own.
The Piped Seam
A seam with a strip of folded fabric, often with a cord inside, caught between the two layers so it shows as a fine line along the seam. It is common on blouses, kurtas and kids' wear as a contrast.
Use it for: armholes, necklines, princess seams and yokes where a defined line adds to the design. It is slower than a plain seam and should be priced as a design addition.
Choosing at a Glance
| Seam | Strength | Inside finish | Best for |
|---|
Plain, finished | Good | Depends on the finish | Most seams, anywhere alteration may be needed |
French | Good | Fully enclosed | Sheer and fine fabrics |
Flat-felled | Very strong | Fully enclosed | Shirts, trousers, uniforms, denim |
Overlocked | Good, stronger with a stitch line | Neat thread edge | Everyday garments and bulk work |
Bound | Good | Fully covered | Unlined jackets and occasion wear |
Lapped or topstitched | Strong | Visible stitching | Yokes, plackets, heavy fabrics |
Piped | Good | Enclosed in the piping | Design lines, necklines, armholes |
Seam Finishes for a Plain Seam
A plain seam needs its raw edges finished, and the choice depends on the fabric and how much time the garment can carry.
Overlocking: the fastest and the most common. Suits nearly every fabric except very sheer ones.
Zigzag stitch: stitched along the raw edge on an ordinary machine with a zigzag setting. A good substitute where there is no overlock machine.
Turned and stitched: the raw edge folded under a little and stitched down. Clean and neat on light and medium cottons, too bulky on heavy ones.
Pinking: cut with pinking shears into a zigzag edge. Quick, but only for fabrics that hardly fray, and for linings that will not be washed often.
Binding: as in the bound seam above. The best looking and the slowest.
Seam Allowance: How Much to Leave
Where | Usual allowance |
|---|
Side seams of blouses and kurtas | 1 to 1.5 inches, so they can be let out later |
Shoulder and armhole seams | Half an inch |
Necklines and curved seams | Quarter to half an inch, clipped |
French seam | About half an inch in total, split between the two passes |
Flat-felled seam | Half to five-eighths of an inch |
Leave more where the customer is likely to change size, and less on curves that have to lie flat. A generous side seam on a blouse is a small cost now and a paid alteration later.
Getting the Seam Right in Practice
Most seam faults have nothing to do with the type of seam and everything to do with the needle, the thread and the pressing. The wrong needle in a fine fabric leaves a seam that puckers whatever seam you choose, so match them first; our guide to needles and thread for each fabric covers it. Press every seam as you go, not only at the end; the pressing and finishing guide shows why.
Teach the seams one at a time to a new karigar, starting with a well-finished plain seam, and do not move on until it is consistent. The first 30 days of training a new karigar sets out a sensible order.
Frequently Asked Questions
What are the main types of seams in tailoring?
The plain seam, the French seam, the flat-felled seam, the overlocked seam, the bound seam, the lapped or topstitched seam and the piped seam. Most garments use a plain or overlocked seam for most of their seams.
Which seam is best for thin fabrics like georgette?
The French seam. It encloses the raw edge completely, so nothing shows through a sheer fabric and nothing frays.
Which seam is the strongest?
The flat-felled seam, which encloses both raw edges and has two rows of stitching. It is used on shirts, trousers, uniforms and denim.
How much seam allowance should a tailor leave?
Usually 1 to 1.5 inches on blouse and kurta side seams so they can be let out later, half an inch at shoulders and armholes, and a quarter to half an inch on necklines and curves.
Where Juvee Helps
The seam a garment needs is a decision the cutter or the karigar makes on every order, and the shop that writes it down gets the same finish every time, whoever stitches it. Juvee carries your instructions to the karigar on each job, with the order, the deadline and the stage it has reached; see tailor job management. The Basic plan is free with no time limit, and paid plans start at ₹10,190 a year including GST; the pricing page lists every plan.